How To Clean Front Load Washer Gasket Mold?

Maintaining a clean and sanitary front-load washer is critical for effective laundry care, but mold in the gasket can become a persistent problem. The plastic gaskets on front-load washers tend to trap water, which makes it easy for mold and mildew to grow. Fixing this problem and getting clean clothes that smell good are essential for the machine’s life. 

In this article, we’ll look at practical methods and critical recommendations for cleaning mold from your front-load washer’s gasket, allowing you to restore cleanliness and efficiency to your laundry routine.

How To Clean Front Load Washer Gasket Mold?

When you clean a mouldy washing machine gasket, you need to focus on both the top surface that you can see and the bottom surface that the water runs off of. Mold often grows in this hidden spot, then spreads to other parts of the machine and onto your clothes.

1. Remove Contents Of Washer And Dispenser Drawers

To avoid accidental bleaching of textiles, always start with an empty washer.

It should be empty if your washer has an automatic dispenser for detergent or fabric softener.

2. Choose The Washer Settings

Choose a standard wash cycle for a heavy load to ensure enough water flows through the machine. Set the temperature of the water to warm or hot.

3. Pour Chlorine Bleach And Start Washer

Depending on the size of the washing drum, put one cup or more of chlorine bleach into it.

Alternatively, put 1/2 cup of liquid chlorine bleach in the dispenser drawer’s detergent compartment and fill the bleach dispenser compartment to the highest level with chlorine bleach. Start the washing and let it run through its entire cycle.

4. Clean Washing Machine Drum And Door

When the cycle ends, dry the washing door and gaskets with a soft, absorbent cloth.

  • These parts should be cleaned and maintained regularly to establish a watertight seal.
  • To clean the inside of a front-load washer, gently peel aside the flexible door gasket. Typically, this is where dirt and detergent residue become stuck, and mold grows.
  • Wearing protective gloves, clean this area with a microfiber cloth or soft-bristled brush dipped in 1/4 cup chlorine bleach and two cups water. Once the mold has been removed, dry the area with a soft towel.

5. Disinfect The Dispenser System

Detergent and fabric softener can accumulate in the dispenser drawers and sustain the odour-causing mold.

To remove remnants of accumulated residue:

  • Rinse the drawer inserts with warm tap water.
  • If the components are extensively coated with built-up residue, immerse them in a basin or pail of hot water for 10 minutes.
  • Allow the drawers to air dry after thoroughly rinsing them.
  • Wearing protective gloves, wipe the washer’s drawer housing with a cloth or soft-bristled brush dipped in a chlorine bleach/water solution. Remove any residue from the recess’s upper and lower portions.
  • After cleaning the drawer and opening it, put the bleach and fabric softener pieces back where they belong.
  • Put the dispenser box back in place and run a short cycle, like the Pre-wash cycle, with no laundry or cleaning products in the drum. This will clean the system thoroughly.

6. Empty The Lint Filter

The lint filter or trap in most washers should be cleaned regularly. Trapped lint might begin to mold and generate stink. Locate and remove the filter.

Wet a cloth and dip it in a chlorine bleach/water solution. Then, use the brush to remove the lint and the fabric to remove germs. Rinse the filter well and let it dry in the air before putting it back in the washer.

How Do You Prevent Mold On A Washing Machine Seal?

1. Keep The Door Open

After each wash cycle, open the washing machine door to allow air to flow and dry out the drum. This helps to avoid moisture build-up, which can contribute to mold formation.

2.Regularly Clean The Detergent Dispenser

Mold can grow in the detergent dispenser tray. Thus, it’s critical to clean it regularly. Remove the tray and thoroughly clean it with warm soapy water. Make sure it’s scorched before putting it back in the machine.

3. Clean The Door And Gasket

Wipe off the interior of the door and the rubber gasket with a clean, dry cloth after each usage. This removes any moisture or residue and aids in the prevention of mold formation.

4. Make Use Of High-Efficiency Detergent

Use High-Efficiency (HE) detergent if you have an HE washer. Non-HE detergent produces an excessive amount of suds, which promotes mold growth. For the same reason, only use the prescribed amount of detergent.

5. Try Not To Overload Machine

Overloading the washing machine might inhibit normal water and detergent circulation, resulting in poor cleaning and mold growth. To guarantee optimal performance, follow the manufacturer’s load size recommendations.

6. Remove The Filter

Lint, dirt, and other particles are trapped by a filter in some washing machines. Regularly review the manufacturer’s instructions on identifying and cleaning the filter. A clogged filter can obstruct water drainage and contribute to a wet environment.

7. Ongoing Maintenance

Follow the manufacturer’s recommendations for regular washing machine maintenance. Professional cleaning or inspections may be required to ensure peak performance and prevent mold growth.

Following the cleaning procedure outlined above, you may efficiently eliminate mold and mildew from the gasket, resulting in a fresh and odor-free washer. Consistent maintenance and frequent cleaning can extend the life of your front-load washer and help you and your family have a healthier and cleaner washing experience.

Thanks for reading the article.

Leave a Comment